A
AnonymousPosted on Aug 09, 2014
Answered
What does 1F mean
- Want Answer0
Clicking this will make more experts see the question and we will remind you when it gets answered.
- Add a Comment
More
- Print this page
Answer This Question
2 Answers
Mike Tellegen
Level 3:
An expert who has achieved level 3 by getting 1000 points
Superstar:
An expert that got20 achievements.
All-Star:
An expert that got10 achievements.
MVP:
An expert that got5 achievements.
- Hayward Master1,631 Answers
- Posted on May 25, 2015
Mike Tellegen
Hayward Master
Level 3:
An expert who has achieved level 3 by getting 1000 points
Superstar:
An expert that got20 achievements.
All-Star:
An expert that got10 achievements.
MVP:
An expert that got5 achievements.
Joined: Aug 05, 2010
Answers
1631
Questions
2
Helped
1017177
Points
5840
FollowView Profile
IF (not 1F) is Lockout
Ignition lock out, means that the heater had three separate attempts to fire up, to have ignition. After three attempts, with no ignition of main burners, you will get the fault code. You clear this by cycling the power off and then back on. You may need to do this 2 or 3 times. Some times air is in the main gas supply line?
Or, Because we are human, we tend to make mistakes, and may overlook the obvious... is the gas valve in the on position? , and is the gas shut off valve on the supply line, open?
if the obvious is all good, then continue with your troubleshooting, next up would be to check the hot surface igniter. or plugged orifice. Especially the most Left one - closest to igniter.
Robco Water
Level 2:
An expert who has achieved level 2 by getting 100 points
All-Star:
An expert that got10 achievements.
MVP:
An expert that got5 achievements.
Champion:
An expert who has answered 200 questions.
- Hayward Expert258 Answers
- Posted on Aug 12, 2014
Robco Water
Hayward Expert
Level 2:
An expert who has achieved level 2 by getting 100 points
All-Star:
An expert that got10 achievements.
MVP:
An expert that got5 achievements.
Champion:
An expert who has answered 200 questions.
Joined: Oct 01, 2012
Answers
258
Questions
Helped
153268
Points
337
FollowView Profile
The code you are referring to is actually IF, not 1F. It stands for ignition failure.
If the control exceeds the maximum number of ignition retries or recycles the heater will shut down and go into lockout. Automatic reset is 60 minutes.
Ad
5 Related Answers
Anonymous
- 5 Answers
- Posted on Jun 07, 2009
SOURCE: Error code LO
Is the heater installed indoors?? if so you'll need a vent pressure orifice kit.
if not check your water press. (below 18 PSI on filter) Place filter on "recir" if it fires and stays on . it's the pressure.
check to see if all connections a set tight hi-ltd switch wire harness etc.
Ad
poolyoda
- 128 Answers
- Posted on Aug 23, 2009
SOURCE: same problem pool heater shows hayward pool heater bo error
BO means that you have bypassed operations. ie automation. if no automation is present then press and hold the Down arrow and Mode button for 3 seconds.
thepool
- 78 Answers
- Posted on Apr 23, 2010
SOURCE: Pool Heater with communication (CE) Error
Code "CE" stands for communication error and describes a fault between the mother board and the display. I doubt it's the relay causing it though...
Anonymous
- 760 Answers
- Posted on Jul 05, 2010
SOURCE: CE error code on hayward pool heater
CE= Communication Error between Control Module
and Display Interface Assembly
1. Disconnect and then reconnect power to heater.
2. Check for faulty wiring or connection.
Inspect Display Interface Wiring. Ensure Display Interface Plug is securely attached to Control Module. .
3. Control Module and/or Display Interface Assembly
are defective.Replace Control Module and/or Display Interface Assembly.
Here is a linkt oH aywardmanuals:
http://www.haywardnet.com/inground/products/manuals.cfm
Anonymous
- 760 Answers
- Posted on Jul 05, 2010
SOURCE: Our Hayward gas heater keeps giving us a H5 error
Could the Error code be HS? That is high temperature limit. Perhaps you' don't have enough flow, allowing the heater to heat the water to a temperature higher, than the thermostat setting. Make sure your bypass valve is closed, allowing full flow through the heater. Check your filter pressure differential , and skimmer baskets.
You didn't give your model number, and there are many models. You can go the Hayward website below and select your exact model number and download the manual. The manual will explain each error code.
http://www.haywardnet.com/inground/products/manuals.cfm
Ad
Add Your Answer
- Video
- Photos
Upload
Upload an image from your computer
×
Uploading: 0%
my-video-file.mp4
Complete. Click "Add" to insert your video. Add
×
Loading...
prevnext
Related Questions:
0helpful
1answer
...on then goes to service and shows 56 Bo means bypass operation which means the heater is being controlled by an outside control.
hayward pool heater service code Questions & Answers (with ...
https://www.fixya.com > Forum > Tagsand also
Make model manual. Should give you trouble codes although they seem to use Letter codes.
..
Read full answer
Jul 25, 2021 •
0helpful
1answer
http://pyrate.org
Read full answer
May 03, 2020 •
0helpful
2answers
its IF. which is an ignition failure
Read full answer
May 08, 2014 •Hayward 250kbtu Ng Pool Heater - Inground
0answers
Read full answer
Be the first to answerApr 26, 2013 •Hayward Pool Products Hayward H250 250k...
2helpful
2answers
"IF" or" Ignition failure", simply means you heater didn't fire. Be sure your gas is on,and if on propane be sure there is at least 30% in the tank (and the valve is open).Also check whether your "Glow plug" ignitor Glows, or your spark ignitor sparks (depending on which kind you have).
Read full answer
Oct 22, 2010 •
1helpful
1answer
It means Ignition Failure. They heater went thru its startup cycle, and when the gas valve opened, the heater did not sense a flame. The whole routine begins again. After about 3 attempts at this, the heater will flash IF and then go into a lockout situation. This is a safety feature of this heater.
Read full answer
May 22, 2010 •Hayward 250FDP Universal Series Propane...
0helpful
1answer
If the heater is cycling on and off continuously the problem may be a dirty filter. Try backwashing and rinsing the filter before anything else.
Read full answer
Jun 28, 2009 •
0helpful
1answer
if = ignition failure. there's a troubleshooting chart in the hayward manual.
Read full answer
Jun 26, 2009 •
0helpful
1answer
This is a code for ignition falure. If you are getting a pilot then it means your Ignition module is not sensing the flame and shuting the gas down. This could be pilot wire burnt and grounding or a pilot flame not reaching the sensor or a bad ignition module. This is the expensive part so look into the other things first. Good luck.
Read full answer
Jun 26, 2009 •Hayward 250kbtu Ng Pool Heater - Inground
